Buy solid wood furniture, grab from the details

Buying solid wood furniture, in addition to looking at the style and size of the furniture, it is necessary to start from the details, carefully selected to pick the right and quality furniture.

1. If the furniture is solid wood made into a really, or indicate where is the wood, where is the wood-based panels.

Peek into the mystery of wood : wood grain and knots . This is the method disclosed by the industry to identify whether it is a piece of solid wood. For example, if a cabinet door looks like a pattern, then the corresponding pattern of the pattern changes, and the corresponding pattern is seen on the back of the cabinet door. If the correspondence is good, it is a pure solid wood cabinet door. Also look at the knot is also a good way to identify pure wood: optimistic about the location of the scar side, and then find the corresponding pattern on the other side.

2, what kind of wood is made of wood, which directly affects the price and quality.

Ordinary solid wood furniture usually uses eucalyptus, white oak, ash, eucalyptus, eucalyptus, rubber wood, eucalyptus, while the precious mahogany furniture mainly uses "rosewood, wenge, rosewood". The market for solid wood furniture is rather chaotic, and there are often things that are shoddy and confusing. It is best to buy brand-name products. At the same time, note that the price of wood can only be higher and higher, and it is too cheap to be fraudulent.

3. Observe the pros and cons of wood.

Open the furniture cabinet door and drawer to observe whether the wood is dry and white, and the texture is tight and delicate. If furniture made of particleboard, MDF, and one-time molded board is used, it is required to open the door or drawer without irritating odor.

4. Observe the wood for defects.

The main stress-bearing parts of the furniture, such as the column and the load-bearing horizontal strip connecting the column to the ground, should not have large knots or cracks or cracks. The structure is firm, the frame must not be loose, and it is not allowed to break or break the material. Don't buy a "three-in-one" that uses a saw to cut a particle board, nail it with a nail, and paint it with a paint. Don't buy a furniture made of "three no" drawers that help you with no bad, no flaws, no straps at the end. . The components of the wood-based panels used in the furniture shall be edge-sealed, and the various accessories shall be installed with few pieces, missing nails and nails.

5. Observe the strength of the board surface.

Board emphasized is finger to feel the fastness of the board. One side of the material should be fixed by a well-shaped solid frame. If the skeleton is sparse, the surface will feel empty and false, and the panel will vibrate greatly. The bottom of the drawer should be pressed by hand to test the strength. Generally, the bottom of the partition is multi-layered and the area is large. The partitions should be made of five-layer boards. Doors and drawers switch to be flexible. When veneer panel cladding and other materials, should be similar to the color of packaged product, the product surface coating does not allow wrinkled skin, sticky lacquer and drain.

6. Observe whether there is a tilting of the drawer or the door frame , whether there is a skew of the position caused by the twisted eye position or the eye hole is too large, and the hoe is not strict.

Wooden furniture should have safety and stability. When the two doors are opened 90 degrees, the hand can be gently pulled forward, the cabinet can not be tilted forward automatically; the glass of the bookcase door should be edging; the mirror and The dressing table should be equipped with a back panel, and the bead should be fixed to the glass surface. Individual parts of the furniture (such as legs, drawers, doors or brackets) must be supported. You should push the top corner of the furniture or sit on one side and try to make sure the furniture is firm.

7. Is the edge, top, front and back interface of the furniture an inlay joint, a tongue-and-groove joint, or a double dowel joint? It is advisable to purchase a dovetail joint or a butterfly joint.

Heavier furniture should be screwed with a protective block in the corner and glued. As for the back plate part, it is also necessary to check whether it is set and the screws are attached.

8. Check the slides and latches of the drawer.

The drawer should be solid and secure with the screws tightened inside. It is a good idea to open the drawers, the event table, the doors and other parts to ensure that they can be used freely and properly connected.

9. Place your hand on the surface of the furniture and carefully check whether the polished surface is smooth. In particular, avoid the roughness of the table legs.

Are there any streaks in the pigment? Are the pigments in the corners too thick? Are there cracks or bubbles?

10. Turn the chair upside down on the furniture and have a look at how they are made.

As for the table, check from the bottom. See if the seams are reinforced with screws and wedges? Is the slats tightly fastened to the crosspieces? There are no excess glue or filler in the seams.

11, pay special attention to the moisture content and origin of solid wood furniture wood.

The climate of various regions in China has an impact on the moisture content of wood. The moisture content of wood should not be higher than 1% of the local equilibrium moisture content of the area of ​​use. Otherwise, the wood will be separated due to expansion and contraction, and the furniture will fall apart. . Therefore, to buy mahogany furniture produced by drying equipment and dry-processed enterprises, mahogany furniture produced locally or in the field is not important. The key is whether the moisture content is consistent with the equilibrium moisture content of the area of ​​use. There is an old saying "solid wood but the Yangtze River", that is to say, after the solid wood furniture produced in the south reaches the north, the moisture content will be affected by the climate, which is prone to cracking and deformation. Therefore, when you purchase, you should see the place of production.

Nature Material

Nature Material

Nature Materials,Synthetic Leather,Polyurethane Leather,Pu Faux Leather

DONGGUAN SHENGYUAN INDUSTRIAL CO,.LTD. , https://www.elementpuleather.com